Corival Supine

Phased out - support up till 2027

The Corival Supine is perfectly suitable to use for ergometry. You can use it for examinations as well, since it is possible to “hide” the ergometer under the table easily. The width of the mattress is 80 cm. The back panel, the shoulder support and the handgrips are adjustable. The ergometer is rotatable in a range of 180° which enables easy adjustment to suit leg length. The Corival Supine is standard supplied with protective earth.

Specifications

Minimum load 7 W the minimum load the ergometer can provide
Maximum peak load 1000 W the maximum load the ergometer can provide for a short period of time
Minimum load increments 1 W the smallest steps with which the load can be added
Maximum continuous load 750 W the maximum power the ergometer can deliver continuous
Hyperbolic workload control
control of workload in hyperbolic way
Linear workload control
control ergometer in a linear way
Fixed torque workload control
control ergometer in a fixed torque way
Maximum rpm independent constant load 150 rpm rpm as to which constant load can be applied
Minimum rpm independent constant load 30 rpm rpm as from which constant load can be applied
Optional heart rate controlled workload
control the device optionally through a set heartrate
Electromagnetic "eddy current" braking system
system that very accurately applies a brake to the ergometer
Dynamic calibration
continuous calibration during application of workload
Workload accuracy below 100 W 3 W accuracy of the ergometer below 100 Watt load
Workload accuracy from 100 to 500 W 3 % accuracy of the ergometer between 100 and 500 Watt
Workload accuracy from 500 to 1000 W 5 % accuracy of the ergometer between 500 and 1000 Watt
Minimum leg length user 640 mm 25.2 inch leg length to fit to pedals
Minimum leg length user (incl. adjustable pedals) 640 mm 25.2 inch leg length to fit to pedals when adjustable cranks are used (measured inseam)
Allowed user weight 200 kg 440.9 lbs maximum patient weight
Pedal shoes
premounted pedal shoes
Adjustability backpanel 34.5 ° degrees from horizontal
Adjustability ergometer 180 ° degrees from horizontal
Readout Distance
Readout the distance on control unit
Readout RPM
Readout the actual rpm on control unit
Readout Heartrate
Readout the actual heartarte on control unit
Readout target HR
Readout target heartarte on control unit (only possible with HR option)
Readout Energy
Readout the energy on control unit
Readout Torque
Readout torque on control unit
Readout Time
Readout time on control unit
Readout Power
Readout the actual power on control unit
Set Display
Choosing parameters to be shown on the display during the stress test
Set Resistance
Possibility to define a specific resistance for each test subject
Set P-Slope
Possibility to set the load regulation resistance
Set Mode
Possibility to define parameters to be adjusted during the stress test
Manual operation mode
Operate manually
Preset protocol operation mode
Operate via preset protocols
Analog operation mode
operate analog
Terminal operation mode
operate with an external device
Selfdesigned protocol operation mode
operate via selfdesigned protocols
Analog connector
read-out of ergometer load in an analog way
Product length (cm) 212 cm 83.5 inch length of product in cm
Product width (cm) 75 cm 29.5 inch width of the product in cm
Product height 118 cm 46.5 inch height of product
Product weight 10 kg 22 lbs the weight of the product
115 V AC 50/60 Hz (138 VA)
operational power
230 V AC 50/60 Hz (138 VA)
operational power
CE class Im according to MDD93/42/EEC
CE certified
CB according to IECEE CB
CB certified
*Specifications are subject to change without notice.

FAQ

backsupport 0-32°; ergometer 0-180°
Your Lode ergometer is standard supplied with one display. The contrast of this display is factory set and can adjusted by qualified service personal only. If your ergometer is supplied with a programmable option the contrast of this display can be set as follows: go to SYSTEM PARAMETERS select SETTINGS go to CONTRAST. Change the visability according your wishes and save the changes.
Yes you can request the actual pedalling speed and power when you are cycling in Manual, Analogue or Terminal mode.
The load will only be returned when the pedalling speed is 30 RPM or more. For technical details see the Lode RS232 protocol
Yes you can. Make sure the chipset used in the converter is from FTDI to have good data acquisition.
Not sure what this means? Contact us and we will help you to get the right converter.

Part number

  • 924900

Certificates

ISO 13485: 2016 Certificate
CE Certificate Stress Test and Force Measurement Devices
ISO 9001:2015 Certificate
IEC 60601-1:2005 – ed. 3 + C1 + C2 (cycle ergometers) certificate
FDA Registration certificate
Manufacturers Declaration of Conformity 23 Lode
UL CSA Corival series certificate

Manuals

M924900 - Manual Corival Supine English

Brochures

Brochure Corival Supine English
pdf
Brochure Corival Supine German
pdf
Brochure Corival Supine Spanish
pdf

Posters

Poster Corival Supine English
Poster Corival Supine German
Poster Corival Supine Spanish

Service

Part number

  • 924900