Angio with table-top frame
Phased out - support up till 2027
Angio ergometer with wheeled frame that makes it very easy to place the ergometer over a patient bed and move it. An rpm / watt meter is standard supplied with this ergometer.
Specifications
| Minimum load | 7 W | the minimum load the ergometer can provide | |
| Maximum peak load | 1000 W | the maximum load the ergometer can provide for a short period of time | |
| Minimum load increments | 1 W | the smallest steps with which the load can be added | |
| Maximum continuous load | 750 W | the maximum power the ergometer can deliver continuous | |
| Hyperbolic workload control | control of workload in hyperbolic way | ||
| Linear workload control | control ergometer in a linear way | ||
| Fixed torque workload control | control ergometer in a fixed torque way | ||
| Maximum rpm independent constant load | 150 rpm | rpm as to which constant load can be applied | |
| Minimum rpm independent constant load | 30 rpm | rpm as from which constant load can be applied | |
| Optional heart rate controlled workload | control the device optionally through a set heartrate | ||
| Electromagnetic "eddy current" braking system | system that very accurately applies a brake to the ergometer | ||
| Dynamic calibration | continuous calibration during application of workload |
| Workload accuracy from 7 to 100 W | 3 W | accuracy of the ergometer between 7 and 100 Watt | |
| Workload accuracy from 100 to 500 W | 3 % | accuracy of the ergometer between 100 and 500 Watt | |
| Workload accuracy from 500 to 1000 W | 5 % | accuracy of the ergometer between 500 and 1000 Watt |
| Readout Distance | Readout the distance on control unit | ||
| Readout RPM | Readout the actual rpm on control unit | ||
| Readout Heartrate | Readout the actual heartarte on control unit | ||
| Readout target HR | Readout target heartarte on control unit (only possible with HR option) | ||
| Readout Energy | Readout the energy on control unit | ||
| Readout Torque | Readout torque on control unit | ||
| Readout Time | Readout time on control unit | ||
| Readout Power | Readout the actual power on control unit | ||
| Set Display | Choosing parameters to be shown on the display during the stress test | ||
| Set Resistance | Possibility to define a specific resistance for each test subject | ||
| Set P-Slope | Possibility to set the load regulation resistance | ||
| Set Mode | Possibility to define parameters to be adjusted during the stress test | ||
| Manual operation mode | Operate manually | ||
| Preset protocol operation mode | Operate via preset protocols | ||
| Analog operation mode | operate analog | ||
| Terminal operation mode | operate with an external device | ||
| External control unit | a control unit is connected with a cable to the ergometer | ||
| Selfdesigned protocol operation mode | operate via selfdesigned protocols |
| Analog connector | read-out of ergometer load in an analog way |
| Maximum table width | 1090 mm | 42.9 inch | maximum distance between the outside of the instrument rails on a patient table |
| Minimum table width | 760 mm | 29.9 inch | minimum distance between the outside of the instrument rails on a patient table |
| 115 V AC 50/60 Hz (138 VA) | operational power | ||
| 230 V AC 50/60 Hz (138 VA) | operational power |
| IEC 60601-1:2005 | the product is IEC 60601-1 3rd edition compliant | ||
| ISO 13485:2016 compliant | Lode fulfils ISO 13485:2016 requirements | ||
| ISO 9001:2015 compliant | Lode fulfills ISO 9001: 2015 requirements |
| CE class Im according to MDD93/42/EEC | CE certified | ||
| CB according to IECEE CB | CB certified |
Accessories
FAQ
Your Lode ergometer is standard supplied with one display. The contrast of this display is factory set and can adjusted by qualified service personal only. If your ergometer is supplied with a programmable option the contrast of this display can be set as follows: go to SYSTEM PARAMETERS select SETTINGS go to CONTRAST. Change the visability according your wishes and save the changes.
Yes you can. Make sure the chipset used in the converter is from FTDI to have good data acquisition.
Not sure what this means? Contact us and we will help you to get the right converter.
Not sure what this means? Contact us and we will help you to get the right converter.
Yes, Due to the fact that the scientific research on the spread of Covid-19 is not yet conclusive Lode recommends to disinfect and clean all Lode products and their accessories (cuffs, heart rate belts, SpO2 sensors, handgrips/rails, touchscreens etc) that are in contact with the patient and or the medical personnel with a standard disinfectant as used in the hospital before and after every patient, with attention and care!
Since these agents are sometimes aggressive it might be advisable to check the effect on sensitive surfaces, like cushioning on non-visible areas. Lode will not take responsibility for discoloration due to these agents.
Since these agents are sometimes aggressive it might be advisable to check the effect on sensitive surfaces, like cushioning on non-visible areas. Lode will not take responsibility for discoloration due to these agents.
Part number
- 917908
Certificates
CE Certificate Stress Test and Force Measurement Devices
ISO 9001:2015 Certificate
IEC 60601-1:2005 – ed. 3 + C1 + C2 (cycle ergometers) certificate
FDA Registration certificate
Manufacturers Declaration of Conformity 27 Lode
UL CSA Angio series certificate
Dimension pictures
Dimensions Table Top Frame Angio - rear view
Dimensions Table Top Frame Angio - side view
Brochures
Posters
Poster Cardio Pulmonary English
Poster Cardio Pulmonary German
Poster Cardio Pulmonary Spanish
Service
Part number
- 917908
